2026-10-03 · 8 min read
Connecting Water, Power and Drainage to an Expandable Container Home
The question every buyer asks after the site is prepared: how does the home actually connect? The honest answer — water, drainage and electrical systems arrive installed and factory-tested, your licensed trades make the site connections at planned points, and the drawings to design all of it are downloadable today.
Site preparation answers where the home sits. The next question buyers ask — usually with a plumber's quote on the desk — is how the home connects: what happens between the unit that arrives folded and a kitchen tap that runs. It is a fair question, because for a folding building the assumption is often that services must be engineered specially. They do not.
The direct answer: the internal systems arrive factory-installed and tested. The plumbing is pressure-tested in the workshop and the electrical system passes a power-on test recorded on video before any unit is packed. Your licensed trades then make ordinary site connections at points that are planned with you in advance — and the drawings that show exactly where those points sit are available now, free, in our Download centre. This guide walks through each system, what the factory does, what your trades do, and how to plan the whole thing before the unit ships.
What arrives done, and what your trades do
The division is simpler than most buyers expect, and it is the same across the range.
| System | Factory side — done and tested before shipping | Your side — ordinary site connection |
|---|---|---|
| Water supply | Plumbing installed and pressure-tested in the workshop | Licensed trade connects the site supply at the planned inlet points |
| Drainage | Hot and cold lines plus drainage routing built to the standard bathroom module | Trench and connect from the unit's outlet points to your site disposal |
| Electrical | Full wiring installed; power-on test performed and recorded on video | Licensed electrician connects site power at the control box per the electrical plan |
| Fixtures & fittings | Walk-in bathroom and fittings installed as standard | Normal commissioning checks, as for any new build |
Water: hot, cold and out
The water system is built around the standard bathroom module, and the factory proves it works before the unit travels: every unit's plumbing is pressure-tested as part of the QC sequence. What your plumber needs to see before connection day is routing, and that is why the 20ft water supply and drainage diagram is downloadable — it traces the hot and cold supply lines and the drainage path for the standard bathroom module, so trenching and inlet positions can be designed from paper rather than by guesswork on site.
One detail matters more than any other for planning: connection points are not fixed by the factory for the factory's convenience. Because layouts are customized per order, points can be positioned to suit your site where the layout allows — which side the services arrive from, where the trench runs, how the unit sits on its pad. That flexibility lives at the drawing stage, which is why the services conversation belongs before order confirmation, not after the truck arrives.
Power: what the electrical drawings show
Two documents cover the electrical side. The dimensioned 20ft floor plan includes the electrical layout — socket positions, lighting, switches and media points — so interior planning happens on the real drawing rather than a sketch. For the flat roof type, a dedicated electrical plan goes further: circuit routing, socket positions, lighting and the placement of the control box, which is the point where your electrician's work begins.
Before packing, the electrical system is proven with a power-on test recorded on video — the same QC discipline that pressure-tests the plumbing. On site, your licensed electrician connects supply at the control box and commissions the system as they would in any new build. Nothing about a folded transport format changes the connection work; it only changes that the wiring was already proven before the unit left Hebei.
Plan the services before the unit ships
The single best-cost move in this whole process is sequencing. Services planned before the order is confirmed can shape the layout — connection side, socket positions, media points, the bathroom module orientation — because layouts are customized per order and confirmed in writing before production. Services planned after delivery inherit the built layout, which usually still works but gives up the flexibility.
For a single unit this is a one-plumber conversation with three drawings open. For a multi-unit program it is the service spine decision from our site planning guide: how far water, power and drainage travel to reach each unit, and how the run is shared. Either way, the three documents — the 20ft floor plan with its electrical layout, the water supply and drainage diagram, and the flat roof electrical plan — are in the Download centre without registration, and your trades can mark them up and send the result back with your enquiry.
Connection day, in the right order
Connection day itself is uneventful when the sequence is right, and uneventful is the goal. The site work comes first: the pad is level with drainage running away, and the trenches for water, power and drainage are in before the truck arrives — our site preparation guide walks through that stage in full. The unit is placed, the wings open, and your trades connect at the points the drawings marked. Commissioning follows as it would for any new build: run the taps, test the circuits, check the bathroom module. Done in that order, the services work is ordinary trade work rather than special engineering — which is the entire point of shipping the systems installed and tested.
Compliance without surprises
The systems are built so that connection in Australia and New Zealand is ordinary trade work. Australia-certified plumbing options and AU-standard window and door options are available across the range, and they are built in during production when your destination market is declared at enquiry — which is why the market belongs in the first message, not the last. Final connections and commissioning belong to licensed local trades, exactly as for any conventional home; and if a buyer is considering a modification to an installed certified system, that is a conversation to have with us before work starts, so the compliance intent of the option is preserved.
Once connected, the systems settle into the ordinary maintenance rhythm described in our care guide — an annual service by your trades and a visual check of everything else. Nothing about the services needs special products or factory visits.
If you are at the planning stage, download the three documents from the Download centre and hand them to your trades — the questions they ask with those drawings in hand are exactly the questions we answer at enquiry. Send us the site sketch, the unit count and the destination port with the marked-up drawings, and we reply with the confirmed layout options, the connection point positions and an indicative quotation.
Frequently asked questions
Do I need specialist trades for a container home?
No. Systems are built to Australian-standard options precisely so licensed local trades can connect and service them as ordinary work — supply at the inlet points, drainage from the outlet points, power at the control box. Nothing in the connection scope is special to the format.
Where exactly are the connection points?
They are documented in the downloadable drawings — the 20ft floor plan shows socket, lighting, switch and media points, and the water diagram traces supply and drainage for the standard bathroom module. Where the layout allows, points can be positioned to suit your site, because layouts are customized per order and confirmed before production.
Are the systems tested before the unit ships?
Yes. Plumbing is pressure-tested in the workshop and the electrical system passes a power-on test recorded on video, both as part of the QC sequence before a professional inspector signs the unit off for packing.
Can we change socket positions or add points?
At the drawing stage, easily — layouts are customized per order, so mark your changes on the floor plan and send them with the enquiry. After production starts, treat the layout as built; changes then are modifications rather than customization, and certified systems should be discussed with us first.
Explore these models
- Double-Wing Expandable Container House — Wings fold down for shipping, open up to a full-width home with veranda options.
- Flat Pack Container House — Panelized units that stack efficiently in a shipping container for low freight cost.
Not sure which format fits your project?
Send your target units, destination port and intended use — we reply with layout options, freight format and an indicative quote.
Start an inquiry