2026-10-24 · 11 min read

Ablution Blocks for Australian Camps: Do You Need a Flat Pack Ablution Block?

Before you order a camp ablution block, three numbers decide its size: the peak headcount on site, the split of that headcount, and the wastewater route. Everything after that is arithmetic.

A camp ablution block is a fixture-counting problem before it is a building problem. The search term a buyer uses is short, but the answer behind it is a set of minimum numbers: how many closets, urinals, hand basins and showers a crew of a given size is entitled to expect. Get those numbers wrong and you either over-order modules, or you hand a site inspector a shortfall that stops the camp opening. Get them right and the module layout falls out of a table rather than a negotiation. On our side of the line the flat pack line is already configured for this work: the factory standard for flat pack container houses describes configurable layouts for site offices, camps and storage with ablutions, and the sliding folding room in the same range ships with a restroom module fitted with twin toilets and wash basins.

Two official regimes set those minimums, and both address temporary and remote sites. WorkSafe Queensland publishes the Managing the work environment and facilities Code of Practice 2021, which sets ratios for any workplace and has a dedicated section on mobile, temporary and remote workplaces. Western Australia goes further: the Construction Camp Regulations fix ratios for a construction camp, defined in those regulations as a camp used for more than three months to accommodate a work force of more than 25 persons, and they carry requirements for closets, laundry, drinking water and plumbing standards alongside the fixture counts.

The minimum fixture ratios you have to clear

Both regimes treat the published ratio as a floor rather than a target. The WorkSafe Queensland code of practice states that the ratios are the minimum standard that should be provided, that the scheduling of worker breaks affects the number of toilets required, and that there should be enough toilets available for the number of workers who may need to use them at the same time. In practice the denominator is the peak headcount on site during a shift, not the total headcount across the project.

There is a second layer above the ratios that catches buyers out. The same code of practice notes that for workplaces within buildings, the National Construction Code sets the ratio of toilets to the number of workers, while the code of practice ratios address workplaces outside a building envelope. A prefabricated ablution module sits between those positions: a structure on a site that behaves like a building. Confirm with the council which ratio will be measured against your module before the order is placed.

FacilityWorkSafe Queensland, facilities Code of Practice 2021Western Australia, Construction Camp Regulations
Male closets1 closet pan per 20 males1 closet per 15 employees
Female closets1 closet pan per 15 females1 closet per 10 employees
Male urinals1 urinal per 25 males1 urinal stall, or 535 mm of urinal space, per 20 employees
Hand wash basins1 per 30 male workers and 1 per 30 female workers, or part thereof1 wash basin per 15 employees, or an equivalent trough with taps 610 mm apart
Showers1 cubicle per 10 workers who may need to shower1 shower per 15 employees
Unisex optionOne unisex facility where 10 or fewer people normally work and two or fewer are of one sex, separated by walls, partitions or doors; one closet pan, one washbasin and means for disposing of sanitary itemsNot provided for in the camp regulations
Closet constructionHinged seat and lid, lighting and ventilation, clear signage, a hinged door that locks from inside on each cubicle, and emergency accessClosets connected to the water carriage system of disposal wherever possible; where not connected, completely fly proof

Turning the ratios into a module split

Apply the ratios to a stated headcount and split and you get a fixture count, and a fixture count plus a wall budget becomes a module count. The table below works through four camp sizes using the WorkSafe Queensland ratios and a stated 70/30 male/female split, with shower figures shown only where the work is dirty, hot or hazardous, which the Queensland code of practice identifies as including mining, firefighting, healthcare, abattoirs, foundry work, welding and police search and rescue.

The split is where the drawing question appears. Every cubicle needs a partition, a door and ventilation, and every module has a finite panel schedule to spend on those. The published 20ft reference layout carries 11 internal partition panels, 3 internal doors and 7 windows, so how many closets a single module can hold is a drawing decision, not a number to assume. Module counts in the table are therefore indicative, and the fixture count per module, the panel schedule and the finished sizes are confirmed per order.

Camp size and splitClosets men / womenUrinalsHand basinsShowers where requiredIndicative module split
12 workers, 8 men and 4 women1 / 10221 ablution module, shower provision as a separate module
30 workers, 21 men and 9 women2 / 11231 ablution module plus 1 shower and laundry module
60 workers, 42 men and 18 women3 / 22362 ablution modules plus 1 shower module
120 workers, 84 men and 36 women5 / 345123 ablution modules plus 2 shower modules

What the factory builds and what your site connects

Flat pack container houses ship as nested, panelised kits: frame, wall panels, floor and roof pack into the smallest possible volume and several units travel inside a standard shipping container. The factory standards behind that format are the same ones we apply across the range, namely a welded galvanized square tube frame, an 18 mm cement board floor with PVC or SPC flooring, 0.4 mm double-sided purification wall panels, and an epoxy primer with two-coat 2K polyurethane topcoat for a long anti-corrosion life.

The fit-out is a drawing per order rather than a catalogue line, and two decisions inside it are worth raising early. The first is the plumbing declaration: Australia-certified plumbing and AU-standard window and door options are available across the range and declared at enquiry, so the certificate status of the closets, pans, traps and taps is part of the specification conversation. The second is the electrical boundary: on the 20ft export specification, note 1 states that the water and electrical systems include indoor portions only, that the purchaser provides the external incoming power supply, and that air conditioning is not included.

The closest published fixture set we can show you is the bathroom module from the 20ft double-wing export specification: a ceramic toilet, an 800 by 1360 mm shower, a 420 by 540 mm wash basin and a mirror cabinet, behind a 750 by 2000 mm aluminium bathroom door. Flat pack ablution module layouts, fixture counts and finished sizes are confirmed per order against the drawings.

  • Factory scope: welded galvanized square tube frame, wall, floor and roof panels, epoxy primer with two-coat 2K polyurethane finish, and the partition, door and window schedule drawn against the fixture plan.
  • Factory scope, declared at enquiry: Australia-certified plumbing, AU-standard window and door options, and the fixture and fitting schedule for each cubicle and basin.
  • Factory scope: the kits are nested for sea freight, so several modules travel inside one standard shipping container and land on site as packs rather than as assembled rooms.
  • Site scope: slab or bearers sized for the module footprint, and the connection of the module to the prepared service trench.
  • Site scope: external incoming power supply, which the purchaser provides, plus any distribution board adjustment the module load requires.
  • Site scope: potable water supply and pressure, the hot water plant for showers, and the wastewater connection or collection system.
  • Site scope: mechanical extract and make-up air where the bathroom compartment is not naturally ventilated.
  • Site scope: the cleaning and waste removal contract, and the consumables and sanitary disposal provision that goes with it.

Wastewater approval is the line that decides your timeline

In New South Wales, installing or altering an on-site sewage management system requires a written council approval under the Local Government Act 1993, lodged as a section 68 approval, and a separate approval to operate before the system is used. Both are separate from a development application and must be in place before work starts. Newcastle City Council requires a site and soil assessment in accordance with AS/NZS 1547:2012, and notes that NSW Health accredits the human waste treatment devices councils accept.

AS/NZS 1547:2012 is where scale becomes a problem. The standard covers on-site domestic wastewater management systems for flows up to 14,000 litres per week from a population equivalent of up to 10 persons, covering water closets, urinals, kitchens, bathrooms and laundries, and it does not cover commercial and industrial sources or stormwater. A camp catchment sized for dozens of workers sits outside that domestic design flow, so the wastewater system has to be designed and approved at camp scale with the council and its environmental health officer, not copied from a single-household septic layout.

Two more rules shape the module. The Western Australia Construction Camp Regulations require closets to be connected to the water carriage system of disposal wherever possible and, where that is not possible, to be constructed so that they are completely fly proof, and they require plumbing fixtures and fittings to accord with the standards under the Water Services Act 2012 and the Plumbers Licensing and Plumbing Standards Regulations 2000. Queensland Health states it plainly in its mass gathering hand hygiene guideline: waste water should never be discharged to the ground surface or into any watercourse, and where hand wash facilities can only be accessed by one sex, for example within a male or female ablution block, the number of them should be proportionate to the split of people using them.

Product certification and the extract rules

Product certification is the other half of the compliance line. Under the Plumbing Code of Australia, certain plumbing and drainage products must be certified and authorised for use, and the WaterMark Schedule of Products lists a purpose-built bathroom module, meaning prefabricated modules with integral components, accessories and fittings designed for direct connection to the water supply and sanitary drainage system, against WMTS-050:2018 Prefabricated modules. WMTS-050 covers shower, bathroom, laundry and kitchen modules. The same schedule carries specifications for sanitary waste flushing and dosing systems in WMTS-504, flushing sinks in WMTS-526 and automatic hand washing stations in WMTS-527, and certified products appear in the WaterMark Product Database with the trade mark displayed.

One mechanical requirement catches ablution modules specifically. Under Part 10.8 of the ABCB Housing Provisions Standard in the NCC 2022, and Volume One F6D4(2), bathroom, kitchen, laundry and sanitary compartment exhaust must discharge outdoors, and where a bathroom or sanitary compartment is not naturally ventilated the extract must be interlocked with the room lighting and continue running for 10 minutes after the light is switched off, with make-up air to AS 1668.2. A closed ablution module with an extract fan wired straight to the light switch does not meet that provision, and the same rules drive the fresh air opening in the cubicle doors.

RequirementOfficial sourceWhat it changes in the module
Minimum closets, urinals and basinsWorkSafe Queensland facilities Code of Practice 2021; WA Construction Camp RegulationsCubicle count, which sets the partition, door and window schedule
Shower provisionFacilities Code of Practice 2021; WA Construction Camp RegulationsA separate shower module, 1.8 m2 floor minimum, partitions at least 1650 mm high
Unisex layoutFacilities Code of Practice 2021One pan, one basin and sanitary disposal, only where 10 or fewer people normally work
Wastewater approvalNSW Local Government Act 1993; AS/NZS 1547:2012Tank and pump sizing, drain run, and the approval timeline before the module lands
Fly-proof closetsWA Construction Camp RegulationsCloset construction where no sewer connection is available
Potable waterWA Construction Camp Regulations; facilities Code of Practice 2021Storage tank cover, and drinking water outlets kept separate from toilets and basins
Plumbing product certificationWaterMark WMTS-050, WMTS-504, WMTS-526, WMTS-527Which closets, pans, traps, taps and basins can be declared on the order
Bathroom extractNCC 2022 Housing Provisions Part 10.8; Volume One F6D4(2)Extract duct run, lighting interlock with 10 minute run-on, and make-up air to AS 1668.2
Servicing and consumablesFacilities Code of Practice 2021Cleaning frequency, toilet paper, soap, drying, rubbish bins and sanitary disposal

The camp ablution order checklist

Every line below is a number or an approval, and each is cheaper to settle before production than after the module is craned onto a prepared slab. None of them is a request for a price quote.

  • Peak headcount on site during a shift, split by sex, and the number of shifts, because the ratios run against who is on site at once rather than the project total.
  • Which regime the camp falls under: the WorkSafe Queensland facilities code of practice, the Western Australia Construction Camp Regulations, or both where the camp spans jurisdictions.
  • Whether the module is treated as a workplace inside a building or as a structure on site, since the NCC ratio and the code of practice ratio are measured differently.
  • Closets, urinals, hand basins and showers required, with the shower decision tied to whether the work is dirty, hot or hazardous.
  • Whether a unisex layout is permitted, which needs 10 or fewer people normally at the workplace, two or fewer workers of one sex, and physical separation for privacy.
  • The wastewater route: a sewer connection, or an on-site system that needs council approval, and if it is New South Wales, the section 68 approval to install and the separate approval to operate, both before use.
  • The wastewater design basis, established at camp scale against the council and the environmental health officer, with AS/NZS 1547:2012 as the reference for the site and soil assessment.
  • The plumbing certification position for every fixture and fitting in the order, checked against the WaterMark schedule rather than accepted on a supplier claim.
  • Ventilation strategy for the bathroom and cubicle doors, including the lighting interlock with 10 minute run-on and the make-up air arrangement.
  • Service scope and the split of responsibility for cleaning, consumables, sanitary disposal and waste removal, plus the module split and finished sizes confirmed per order against the drawings.

Send the numbers rather than a shopping list and the reply is specific: peak headcount with the split and shift pattern, the wastewater route, the destination council, whether showers are in scope, and how many modules you want on site. You get back the confirmed layout, the specification, the packing format and an indicative quotation, with the module split drawn against the fixture count rather than guessed.

Two documents shorten that conversation. The full specification table at /specifications/ lists every verified figure for every format in one comparable place, and the Download centre holds the dimensioned 20ft floor plan with electrical and plumbing layout, the water supply and drainage diagram for the standard bathroom module, and the flat roof electrical plan showing circuit routing, socket positions, lighting and control box placement. Read the water supply and drainage diagram next to your council approval drawings, because the module-side connection points on that drawing are the same points your plumber will find on site.

Annual production capacity runs at 800 to 1000 sets, and hundreds of these homes have been delivered to Australian customers over the past two years, so a camp programme is a production schedule rather than a one-off enquiry. What stays confirmed per order is everything that changes with the headcount: the fixture schedule, the partition and door layout, the plumbing declaration, and the module split that satisfies the ratios for your site.

Frequently asked questions

Do I need council approval for a container ablution block in Australia?

On the wastewater side, usually yes. In New South Wales, installing or altering an on-site sewage management system requires a written council approval under the Local Government Act 1993, plus a separate approval to operate before the system is used, and both are separate from a development application. The Western Australia Construction Camp Regulations require closets to be connected to the water carriage system of disposal wherever possible and, where that is not possible, to be completely fly proof. Whether the module itself needs a building approval is a separate question that depends on how the council treats a prefabricated structure on your site, so confirm both before the order is placed.

How many toilets do I need for a 30-person construction camp?

It depends on which regime applies and on the sex split. The WorkSafe Queensland facilities code of practice sets 1 closet pan per 20 males and 1 per 15 females, 1 urinal per 25 males, 1 hand basin per 30 male and per 30 female workers, and 1 shower cubicle per 10 workers who may need to shower. The Western Australia Construction Camp Regulations are tighter for males and females alike at 1 closet per 15 and 1 per 10 employees respectively, with basins per 15 employees and showers per 15. A 30-worker camp with a 70/30 split therefore needs 2 male closets, 1 female closet, 1 urinal, 2 basins and 3 showers under the Queensland code of practice, and the count is based on the peak headcount on a shift rather than the project total.

Can a flat pack ablution block be shipped to a remote mine site?

Yes, and the flat pack format is the reason. The kits are nested for sea freight, so several modules travel inside one standard shipping container and land as packs rather than as assembled rooms, which keeps freight cost per unit down on remote routes. What still has to happen on site is the slab or bearers, the external incoming power supply that the purchaser provides, the potable water and hot water plant, and the wastewater connection or collection system. Module counts, fixture schedules and finished sizes are confirmed per order.

Does a container ablution block need to be WaterMark certified?

The plumbing products inside it do. Under the Plumbing Code of Australia, certain plumbing and drainage products must be certified and authorised for use in an installation, and the WaterMark Schedule of Products lists a purpose-built bathroom module against WMTS-050:2018 Prefabricated modules, which covers shower, bathroom, laundry and kitchen modules with integral components designed for direct connection to water supply and sanitary drainage. The schedule also carries WMTS-504 for sanitary waste flushing and dosing systems, WMTS-526 for flushing sinks and WMTS-527 for automatic hand washing stations. Declare the fixtures at enquiry, because the certified item list is part of the order rather than something added on site.

How many showers do camp ablution modules need?

One shower cubicle for every 10 workers who may need to shower under the WorkSafe Queensland facilities code of practice, and one shower per 15 employees under the Western Australia Construction Camp Regulations. The requirement is triggered by dirty, hot or hazardous work, with mining, firefighting, healthcare, abattoirs, foundry work, welding and police search and rescue named as examples. The build specification matters as much as the count: floor area of not less than 1.8 m2, a slip-resistant surface capable of being sanitised, partitions at least 1650 mm high and no more than 300 mm above the floor, an adjacent dressing area with a seat and hooks, a lockable door, clean hot and cold water, and individual non-irritating soap.

Related guides

Explore these models

Not sure which format fits your project?

Send your target units, destination port and intended use — we reply with layout options, freight format and an indicative quote.

Start an inquiry