2026-09-27 · 8 min read
20ft, 30ft or 40ft? Choosing the Right Expandable Container Home Size
Length is the first decision that is expensive to change later. This is how to choose between 20ft, 30ft and 40ft double-wing homes — starting from who is staying and how long, then checking the three site conditions that can rule a size out.
Buyers usually arrive with a price bracket and a rough idea, then ask which size to order. It is the right first question, because the footprint drives almost everything downstream: how many service connections each unit needs, how much ground has to be prepared, how the load is handled on arrival, and how much site labour the connections take. Changing a colour or a window is easy. Changing the length after the frame is welded is not.
Our double-wing line is built in 20ft, 30ft and 40ft formats on one construction standard — galvanized frame with eight container corners, 18 mm cement board floor, purification panel interior, and factory-sealed roof folds, with gable and flat roof types across the range. So the decision is not about quality; it is about fit. This is the selection logic we work through with Australian and New Zealand buyers before a size is confirmed.
Start with occupants and stay length, not floor area
The instinct is to compare square metres. A more useful starting point is who will occupy the unit and for how long, because that determines how many separate spaces you need rather than how much floor you can buy. A unit used for short-stay couples has different requirements from one housing a family for a season, and a site office has different requirements from both — yet all three can look similar in area terms.
Once you know the occupancy pattern, the size usually falls out of it. The table below sets out what each length typically suits; final dimensions and layouts are confirmed per order, because layouts are customised per market and the reference floor plans we provide are the starting point rather than a fixed catalogue.
| Format | Typically suits | What to check |
|---|---|---|
| 20ft | Couples, solo workers and short stays; the densest way to house a given number of people | Reference floor plan and specification sheet are available to download as the planning baseline |
| 30ft | Families and longer stays where living and sleeping areas need separation | Longer footprint changes service spine layout and the number of connections per unit |
| 40ft | Shared living, staff housing and units doubling as communal space | Confirm route access and pad size before ordering; the longest format needs the most room to place |
| Mixed sizes on one site | Parks and camps with several occupant types | Order the same construction standard across the mix so maintenance and spares stay simple |
What actually changes as the footprint grows
Four things scale with length, and each one has a cost or a site implication. The footprint itself is obvious, but it is the least interesting of the four.
The second is service connections. Each unit needs water, power and drainage brought to its connection points, and on a multi-unit site every additional branch run is real trenching and real labour. This is why grouping units along one service spine matters more as average unit size grows — the saving is larger when each connection is longer.
The third is ground preparation. A longer footprint needs a longer level, stable foundation to open square onto, because a folded home only opens correctly onto a square base. On sloping sites this is where a 40ft decision is really made, not in the quotation.
The fourth is handling and access. Every HuoSheng home carries eight galvanized container corners and is handled like a standard container, so the lifting method itself does not change with length — but the space needed to place the unit and swing the load does. Our site preparation guide covers the access route and utility marking stage in detail; on a long unit, work through it before confirming the size.
The three checks to complete before you lock a size
These three questions decide more orders than any preference for floor area. Answer them before you confirm the format, and the size decision becomes straightforward.
- Access: can a truck and the lifting equipment reach the exact final position of the longest unit in your mix, without overhead obstruction or a turn the load cannot make?
- Ground: can a level, stable pad of the required footprint be prepared where that unit will sit, including on any slope?
- Services: how far does water, power and drainage have to travel to reach each unit, and does the available spine capacity support the sizes you are considering?
Roof type is a separate choice from size
It is worth separating these two decisions, because buyers often assume a longer unit must take a particular roof. It does not. The gable roof type gives 2.3 m internal height with a pitched profile that sheds rain and snow, which is why it is the popular choice in European and American markets. The flat roof type was developed for Australia and gives 2.4 m internal clearance on the same footprint.
Both roof types are available across the formats, and both fold to the same transport logic, so you are not forced into a length by a roof preference. If extra internal clearance matters for your market — for example on a site where the units will run warm — the flat roof type is the specification conversation to have, independent of whether the order is 20ft, 30ft or 40ft.
For the flat roof type specifically, the electrical layout plan is available in our Download centre, which is useful for planning socket positions and control box placement before the units arrive.
Where buyers get the size wrong
Three patterns come up repeatedly, and all three are avoidable at the planning stage.
The first is ordering by area alone. A larger unit with an unsuitable internal layout wastes floor space, while a smaller unit with the right layout can house the same number of people more comfortably. Layout is confirmed per order, so use that flexibility before you size up.
The second is ignoring the service spine until after the units are ordered. By then the size is fixed and the trenching has to be designed around it. Planning services first, then choosing sizes to fit the spine, is almost always cheaper.
The third is assuming one size for the whole site. A park that houses couples as well as families will usually run better with a mix — the same format and construction standard, but sized to the occupant — rather than uniform units that are oversized for some pitches and undersized for others.
None of this requires a factory visit. Download the 20ft reference floor plan and the 20ft specification sheet from our Download centre, note the layout your market needs, then check the three site conditions above. When those are settled, send us your intended unit mix, destination port and site location — we reply with layout options for each length, the freight format and an indicative quotation, and we can confirm which parts of your mix change the packing and delivery sequence.
Frequently asked questions
Which size is most popular for holiday parks?
It depends on your guest profile rather than a single industry answer. Parks housing couples and short stays usually find the smaller format gives more pitches per hectare, while those with longer family stays lean longer. Many operators run a mix of sizes on one site using the same construction standard.
Can I extend or resize a unit after delivery?
The format and layout are confirmed before production, so treat the size as final once the order is locked. Multiple units placed on one site can be added in stages instead, which is how many park and camp operators expand capacity without committing to their full footprint up front.
Do longer units need a bigger crane?
Every unit carries eight galvanized container corners and is handled like a standard container, so the lifting method stays consistent across the range. What changes with length is the space needed to place the unit and swing the load — that is confirmed per order as part of the packing plan.
Is the internal height different between the sizes?
Internal height follows the roof type, not the length. The gable roof type gives 2.3 m and the flat roof type, developed for Australia, gives 2.4 m — on any of the available formats. If clearance matters for your market, choose the roof type first and the length second.
Related guides
Explore these models
- Double-Wing Expandable Container House — Wings fold down for shipping, open up to a full-width home with veranda options.
- Flat Pack Container House — Panelized units that stack efficiently in a shipping container for low freight cost.
Not sure which format fits your project?
Send your target units, destination port and intended use — we reply with layout options, freight format and an indicative quote.
Start an inquiry